Large-sized single-edged pliers that can cut 5mm diameter plastics!
Because it is a single-edged design, no flying debris will be generated!
In addition to nozzle cutting, it is also very convenient for removing burrs!
It can also handle hard transparent materials, with a maximum cutting diameter of 3mm! GodHand Large Size Single-Edge Bevel Pliers——Powerful cutting of thick sprues!
Φ5mm large size single-edge design, easily flattening sprues without leaving marks!
✔ Super cutting force: specially designed for thick sprues and runners, can cut plastics with a diameter of up to Φ5mm!
✔Applicable to transparent parts: Hard transparent plastics (such as PS, ABS) can also be cut, with a maximum of Φ3mm (general single-edged pliers can only cut Φ2mm).
✔Compatible with resin models: Even the injection port of resin castings can be processed!
✔Single-edged precision structure: The cut surface is smooth and without visible marks, and the cut naturally fits the edge of the part!
Product Features
🔹Extended blade: The effective blade length is about 16mm, which makes cutting easier and can also be used to trim burrs!
🔹“Cutting blade” design: Through precision craftsmanship, the “cutting blade” is slightly convex than the “cutting blade” to ensure that it remains sharp and reduces looseness after long-term use!
🔹Two-stage cutting technique (see the tutorial below) can completely flatten the water outlet, leaving almost no trace!
Specifications
・Total length: Approx. 160mm
・Effective blade length: Approx. 16mm
・Applicable materials: Plastics (PS, PP, ABS, PE)
・Cutting capacity:
– General plastics: Φ5mm or less
– Transparent/translucent hard plastics (such as PS, ABS): Φ3mm ❶ Cut the sprue slightly away from the part (first cut)
❷ Slide the cutting blade into the joint surface of the part
❸ Keep the cutting blade close to the side of the part
❹ Flatten the sprue while keeping the cutting blade close to the part (second cut)
⚠Notes
・The spring at the bottom may fall off when the handle is fully opened, so please use it with caution
・If you suddenly release your fingers from the state of gripping the handle, the handle may spring open quickly and the spring at the bottom may fly out. Please open and close gently
・The part closer to the tip of the blade is thinner and easier to damage, so please try to cut near the center of the blade. Please be especially careful when cutting rough plastic
・Do not twist the blade during or after cutting. Twisting will cause load concentration and may cause the blade to break
・Do not cut objects that exceed the length of the blade. In particular, if you cut only with the tip of the blade, the blade will be subjected to excessive load at a certain point, which may cause bending or breaking
・Do not use for cutting plastic sheets, labels, part separation, tenon cutting, etc. Improper use may cause the blade to chip or break
・Even if light force can cut, please do not hold it too tightly
・Do not twist the blade during cutting or when removing it from the flow channel after cutting. Twisting will cause load concentration and may damage the blade
・Do not cut objects that exceed the length of the blade. It will cause excessive load on a certain point of the blade, which may cause bending or breaking
・Do not use it to cut coarse plastics or unsuitable materials (metal, resin, paper, etc.) that exceed the cutting capacity
・Please use a toothbrush or other device to remove debris from the blade during or after use. If debris is left during cutting, it will cause unnecessary load and may cause damage. In particular, if you hold it tightly with debris stuck at the root of the blade, it is easy to cause gaps in the movable parts
・Please do not touch the tip of the "cutting blade" directly with your hands. The "cutting blade" is very sharp and may cause injury
・Sebum will cause rust. If you touch the metal part directly, please wipe off fingerprints and apply rust-proof oil. Humidity will also cause rust, so please oil it frequently during the rainy season
・Deterioration in the lubrication performance of the movable parts will cause shaft wear, and the cutting performance may be reduced due to the gap. Please add lubricating oil to the movable parts regularly
・Please wear goggles for safety
・The cut object may fly. Please make sure that there are no people and fragile objects around before working
・Please keep out of the reach of children
・When not in use, please install the included bevel pliers protective cover, etc., and pay attention to safety
//www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-800x800.jpg 800w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-280x280.jpg 280w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-768x768.jpg 768w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-340x340.jpg 340w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-560x560.jpg 560w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-100x100.jpg 100w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-50x50.jpg 50w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4.jpg 1000w" sizes="auto, (max-width: 400px) 100vw, 400px" draggable="false">
⚠Notes
・The spring at the bottom may fall off when the handle is fully opened, so use with caution
・When you suddenly release your fingers from the state of holding the handle tightly, the handle may pop open quickly and cause the spring at the bottom to fly out. Please open and close gently
・The part closer to the tip of the blade is thinner and easier to damage, so please try to cut near the center of the blade. Please pay special attention when cutting rough plastic
・Do not twist the blade during or after cutting. Twisting will cause load concentration and may cause the blade to break
・Do not cut objects that exceed the length of the blade. In particular, if you cut with only the tip of the blade, the blade will be subjected to excessive load at a certain point, which may cause bending or breaking
・Do not use for cutting plastic sheets, labels, part splitting, tenon cutting, etc. Improper use may cause the blade to chip or break.
・Even if light force can cut, please do not hold it too tightly
・Do not twist the blade during cutting or when removing it from the flow channel after cutting. Twisting will cause load concentration and may damage the blade
・Do not cut objects that exceed the length of the blade. It will cause excessive load on a certain point of the blade, which may cause bending or breaking
・Do not use it to cut coarse plastics or unsuitable materials (metal, resin, paper, etc.) that exceed the cutting capacity
・Please use a toothbrush or other device to remove debris from the blade during or after use. If you cut with debris left, it will cause unnecessary load and may cause damage. In particular, if you hold the blade tightly with debris caught at the base of the blade, it is easy to cause gaps in the moving parts.
・Please do not touch the tip of the "cutting blade" directly with your hands. The "cutting blade" is very sharp and may cause injuries.
・Sebum will cause rust. If you touch the metal part directly, wipe off your fingerprints and apply rust-proof oil. Humidity will also cause rust, so please oil it frequently during the rainy season.
・A decrease in the lubrication performance of the moving parts will cause wear on the shaft, which may reduce the cutting performance due to gaps. Please add lubricating oil to the moving parts regularly.
・Please wear goggles for safety.
・The cut material may fly around. Please make sure there are no people and fragile objects around before working.
・Please keep out of the reach of children.
・When not in use, please install the included bevel pliers protective cover and pay attention to safety.
//www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-800x800.jpg 800w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-280x280.jpg 280w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-768x768.jpg 768w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-340x340.jpg 340w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-560x560.jpg 560w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-100x100.jpg 100w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4-50x50.jpg 50w, https://www.hobbylandeshop.com/storage/2025/05/gh-pn-95-m-c1-4.jpg 1000w" sizes="auto, (max-width: 400px) 100vw, 400px" draggable="false">
⚠Notes
・The spring at the bottom may fall off when the handle is fully opened, so use with caution
・When you suddenly release your fingers from the state of holding the handle tightly, the handle may pop open quickly and cause the spring at the bottom to fly out. Please open and close gently
・The part closer to the tip of the blade is thinner and easier to damage, so please try to cut near the center of the blade. Please pay special attention when cutting rough plastic
・Do not twist the blade during or after cutting. Twisting will cause load concentration and may cause the blade to break
・Do not cut objects that exceed the length of the blade. In particular, if you cut with only the tip of the blade, the blade will be subjected to excessive load at a certain point, which may cause bending or breaking
・Do not use for cutting plastic sheets, labels, part splitting, tenon cutting, etc. Improper use may cause the blade to chip or break.
・Even if light force can cut, please do not hold it too tightly
・Do not twist the blade during cutting or when removing it from the flow channel after cutting. Twisting will cause load concentration and may damage the blade
・Do not cut objects that exceed the length of the blade. It will cause excessive load on a certain point of the blade, which may cause bending or breaking
・Do not use it to cut coarse plastics or unsuitable materials (metal, resin, paper, etc.) that exceed the cutting capacity
・Please use a toothbrush or other device to remove debris from the blade during or after use. If you cut with debris left, it will cause unnecessary load and may cause damage. In particular, if you hold the blade tightly with debris caught at the base of the blade, it is easy to cause gaps in the moving parts.
・Please do not touch the tip of the "cutting blade" directly with your hands. The "cutting blade" is very sharp and may cause injuries.
・Sebum will cause rust. If you touch the metal part directly, wipe off your fingerprints and apply rust-proof oil. Humidity will also cause rust, so please oil it frequently during the rainy season.
・A decrease in the lubrication performance of the moving parts will cause wear on the shaft, which may reduce the cutting performance due to gaps. Please add lubricating oil to the moving parts regularly.
・Please wear goggles for safety.
・The cut material may fly around. Please make sure there are no people and fragile objects around before working.
・Please keep out of the reach of children.
・When not in use, please install the included bevel pliers protective cover and pay attention to safety.
com/storage/2025/05/gh-pn-95-m-c1-4.jpg 1000w" sizes="auto, (max-width: 400px) 100vw, 400px" draggable="false">
⚠Notes
・The spring at the bottom may fall off when the handle is fully opened, so please use it with caution
・When you suddenly release your fingers from the state of holding the handle tightly, the handle may spring open quickly and cause the spring at the bottom to fly out. Please open and close gently
・The part closer to the tip of the blade is thinner and easier to damage, so please try to cut near the center of the blade. Please be especially careful when cutting rough plastic
・Do not twist the blade during or after cutting. Twisting will cause load concentration and may break the blade.
・Do not cut objects that exceed the length of the blade. In particular, if only the tip of the blade is used for cutting, excessive load will be placed on a certain point of the blade, which may cause bending or breaking.
・Do not use for cutting plastic sheets, labels, part separation, tenon cutting, etc. Improper use may cause the blade to chip or break.
・Even if light force can cut, please do not hold it too tightly.
・Do not twist the blade during or after cutting to remove it from the flow channel. Twisting will cause load concentration and may damage the blade.
・Do not cut objects that exceed the length of the blade. This will cause excessive load on a certain point of the blade, which may cause bending or breaking.
・Do not use to cut coarse plastics or unsuitable materials (metal, resin, paper, etc.) that exceed the cutting capacity.
・Remove debris from the blade with a toothbrush during or after use. Cutting with residual debris will cause unnecessary load and may cause damage. In particular, if you hold the blade tightly with debris stuck at the base of the blade, it is easy to cause gaps in the movable parts.
・Do not touch the tip of the "cutting blade" directly with your hands. The "cutting blade" is very sharp and may cause injury.
・Sebum can cause rust. If you come into direct contact with metal parts, wipe off fingerprints and apply rust-proof oil. Humidity can also cause rust, so apply oil frequently during the rainy season.
・A reduction in the lubrication performance of the movable parts can cause wear on the shaft, which may reduce cutting performance due to clearance. Please add lubricating oil to the movable parts regularly
・For safety, please wear goggles
・The cut material may fly. Please make sure that there are no people or fragile objects around before working
・Please keep out of the reach of children
・When not in use, please attach the included bevel pliers protective cover, etc., and pay attention to safety
com/storage/2025/05/gh-pn-95-m-c1-4.jpg 1000w" sizes="auto, (max-width: 400px) 100vw, 400px" draggable="false">
⚠Notes
・The spring at the bottom may fall off when the handle is fully opened, so please use it with caution
・When you suddenly release your fingers from the state of holding the handle tightly, the handle may spring open quickly and cause the spring at the bottom to fly out. Please open and close gently
・The part closer to the tip of the blade is thinner and easier to damage, so please try to cut near the center of the blade. Please be especially careful when cutting rough plastic
・Do not twist the blade during or after cutting. Twisting will cause load concentration and may break the blade.
・Do not cut objects that exceed the length of the blade. In particular, if only the tip of the blade is used for cutting, excessive load will be placed on a certain point of the blade, which may cause bending or breaking.
・Do not use for cutting plastic sheets, labels, part separation, tenon cutting, etc. Improper use may cause the blade to chip or break.
・Even if light force can cut, please do not hold it too tightly.
・Do not twist the blade during or after cutting to remove it from the flow channel. Twisting will cause load concentration and may damage the blade.
・Do not cut objects that exceed the length of the blade. This will cause excessive load on a certain point of the blade, which may cause bending or breaking.
・Do not use to cut coarse plastics or unsuitable materials (metal, resin, paper, etc.) that exceed the cutting capacity.
・Remove debris from the blade with a toothbrush during or after use. Cutting with residual debris will cause unnecessary load and may cause damage. In particular, if you hold the blade tightly with debris stuck at the base of the blade, it is easy to cause gaps in the movable parts.
・Do not touch the tip of the "cutting blade" directly with your hands. The "cutting blade" is very sharp and may cause injury.
・Sebum can cause rust. If you come into direct contact with metal parts, wipe off fingerprints and apply rust-proof oil. Humidity can also cause rust, so apply oil frequently during the rainy season.
・A reduction in the lubrication performance of the movable parts can cause wear on the shaft, which may reduce cutting performance due to clearance. Please add lubricating oil to the movable parts regularly
・For safety, please wear goggles
・The cut material may fly. Please make sure that there are no people or fragile objects around before working
・Please keep out of the reach of children
・When not in use, please attach the included bevel pliers protective cover, etc., and pay attention to safety
400px" draggable="false">
⚠Notes
・The spring at the bottom may fall off when the handle is fully opened, so use with caution
・When you suddenly release your fingers from the state of holding the handle tightly, the handle may spring open quickly and cause the spring at the bottom to fly out. Please open and close gently
・The part closer to the tip of the blade is thinner and easier to damage, so try to cut near the center of the blade. Please pay special attention when cutting rough plastic
・Do not twist the blade during or after cutting. Twisting will cause load concentration and may break the blade
・Do not cut objects that exceed the length of the blade. In particular, if you cut with only the tip of the blade, the blade will be overloaded at one point, which may cause it to bend or break.
・Do not use for cutting plastic sheets, labels, part splitting, tenon cutting, etc. Improper use may cause the blade to chip or break.
・Even if it can cut with light force, please do not hold it too tightly.
・Do not twist the blade during cutting or when you want to remove the blade from the flow channel after cutting. Twisting will cause load concentration and may damage the blade.
・Do not cut objects that exceed the length of the blade. The blade will be overloaded at one point, which may cause it to bend or break.
・Do not use it to cut rough plastics or unsuitable materials (metal, resin, paper, etc.) that exceed its cutting capacity.
・Please use a toothbrush or other device to remove debris from the blade during or after use. If you cut with debris left, it will cause unnecessary load and may cause damage. In particular, if you hold the blade tightly with debris caught at the base of the blade, it is easy to cause gaps in the moving parts.
・Please do not touch the tip of the "cutting blade" directly with your hands. The "cutting blade" is very sharp and may cause injuries.
・Sebum will cause rust. If you touch the metal part directly, wipe off your fingerprints and apply rust-proof oil. Humidity will also cause rust, so please oil it frequently during the rainy season.
・A decrease in the lubrication performance of the moving parts will cause wear on the shaft, which may reduce the cutting performance due to gaps. Please add lubricating oil to the moving parts regularly.
・Please wear goggles for safety.
・The cut material may fly around. Please make sure there are no people and fragile objects around before working.
・Please keep out of the reach of children.
・When not in use, please install the included bevel pliers protective cover and pay attention to safety.
![GODHAND GH-PN-160-GT Single-edged Pliers [Online store only, limit 1 piece per person]](http://sourcexpress.asia/cdn/shop/files/1_000000005054-560x560.jpg?v=1752735399&width=1445)